利用空间多普勒调谐技术冷却原子及其速度单一化

本文理论计算了用圆锥管内多次全反射激光而产生的多普勒频移来冷却原子束的机制。给出了最佳冷却原子束的圆锥管的夹角、长度、反射次数及激光入、出射角等参数。理论计算了原子束经过圆锥管冷却的速度分布情况。数值计算结果表明：采用两个长１３０ｃｍ的锥形管来冷却原子束，选用合适的失谐量可使极大部分速度小于１２００ｍ／ｓ的原子冷却到８ｌｍ／ｓ，并且可得到单一速度的高亮度的原子束。     

《未来加工工业的材料技术》要点及对我国传统产业改造与新材料研发的启示

概述了美国国家材料咨询委员会报告《未来加工工业的材料技术－管理战略和研究机会》要点，对比了美国“未来工业”与中国“传统产业”，鉴于两者的诸多相似特征，指出了该报告中所提出的“市场推动”和“共性技术”开发策略对于中国传统产业改造的借鉴意义，并探讨了报告中所建议的项目管理战略对于中国新材料研发工作的启示。     

Application of a Compaction Simulator to the Design of a High-Dose Tablet Formulation. Part I

The compaction properties of an investigational drug are studied by the use of a compaction simulator. The effects of punch velocity over the range of 30-640 mm^-1 on the compaction properties of the pure drug and a variety of formulas incorporating a high dose of the active compound have been investigated. The data were analyzed by applying the Heckel equation. The pure drug was found to have a high yield pressure at a relatively low punch velocity of 31 mm^-1. As the punch velocity was increased there was a decrease in crushing strength, primarily as a result of increasing yield pressure. These findings indicate that the pure drug predominantly consolidated by fragmentation and elastic deformation, with a slow plastically deforming component. The information obtained on the consolidation mechanism of the pure drug and, subsequently, on model formulas were instrumental in the design and selection of a robust formula and granulation process. The advantages of conducting dosage form design and characterization studies during the early phase of tablet formulation using means such as a compaction simulator are emphasized in this investigation.     

钢筋混凝土烟囱有井架整体爬模施工技术

本文主要 根 据三 明 钢铁 厂130m~2 烧 结机 改造 工 程 60m 和 100m 烟 囱 的施 工实 例 ,详 细介 绍 了钢 筋 混凝 土烟 囱 有井架 整 体爬 模的 施 工新 方 法,并 取 得了 良好 的 效果 。     

关于起重机接地形式的现场检验

由于对低压电力网接地形式理解上的异议，长时间以来在起重机接地的检验中把握尺度不同，作为起重机械现场检验的重要项目，检验结论必须严谨准确、果断周细。     

循环经济理念下的水资源管理模式研究

对循环经济理念的水资源管理及文献进行了综述,阐述了循环经济的基本概念、理论及相关的实践.最后,对于循环经济在水资源管理方面的运用进行了相关研究.     

圆管流动的二次转捩

利用直接数值模拟方法求解N-S方程来研究空间发展的圆管转捩,计算中雷诺数Re选定为3000。在局部壁面引入的周期性吹吸(PSB)扰动作用下,圆管中首先出现了塞流结构,并向下游迁移,同时有稳定的流向条带结构形成;在塞流结构离开计算域后,随着扰动的不断发展,流向条带结构逐渐破裂失稳,圆管流动出现了第二次转捩,这是一种新的转捩形式,我们称之为“二次转捩”。     

基于协方差矩阵变换的相干源个数估计

正确地估计信号源个数是高分辨阵列信号处理的一个重要组成部分,本文提出了一种相干源个数估计的方法。这种方法是先采用空间平滑技术对信号源去相关,然后对阵列协方差进行酉变换,最后用基于协方差矩阵变换的信息论准则和盖氏半径(Gerschgorin Radii)两种方法估计信号源个数。计算机仿真结果证实了方法的可行性。     

Analyses and Solutions of Specific Cases in Spatial Angles Calculation

1 Introduction “Spatial Angles Calculations” means that all the calculations of given and unknown parameters are related to calculating angles in 3D space. The functions and relevant parameters in 3D space are much more complicated than that in 2D space, i.e. on a plane. Professor Sun, based on his research conducting for more than a decade, presented a series of new algorithms to calculate angles in space which are valuable in both theory and applications[1]. The authors found that, in g…